Форум » Спутниковые ресиверы HD » CTech ET9000 Enigma 2 Twin Tuner » Ответить
CTech ET9000 Enigma 2 Twin Tuner
kladovchk: [copyright]CTech ET9000 Enigma 2 Twin Tuner[/copyright] Linux для всех - это девиз Clarke-Tech ET9000. Немецкий производитель Clarke-Tech представила новую модель ET 9000 на основе системы Linux операционной Enigma2 спутниковый тюнер Twin. Новое поколение Clarke-Tech ET9000 так, что она становится очень конкурентоспособным для Vu+ Duo или Dreambox. С открытым исходным кодом Linux OS (Enigma2) 400 МГц MIPS Broadcom 7405 процессор Twin DVB-S2 тюнера (Silicon тюнер) Аппаратное декодирование MPEG2 / H.264 (DVB-совместимый) 16-значный буквенно-цифровой дисплей VFD 2x Общий интерфейс слот для модуля декодирования 2 читателя (Conax Embedded) Сетевой интерфейс 10/100 Мбит / с Ethernet 3x USB 2.0 (1x передняя панель / задняя панель 2) 1 х внутренний разъем SATA для подключения HDD (жесткий диск не входит в комплект) Экстен 1x E-SATA разъем 1x последовательный интерфейс V.24/RS232 HDMI разъем 2x Scart 1 компонентный выход YPrPb 1 х оптический S / PDIF Изменение каналов быстрее чем за 1 секунду EPG (электронный программный гид) Поддержка плагинов (JPEG, MP3, DivX ...) поддержку своих списков каналов Многоязычный OSD, поддержка скинов полностью автоматический и ручной поиск каналов Videotext, телетекст DiSEqC 1,0, 1,1 и 1,2 Видео: Видео-разрешение (720 х 576 линий), 576p, 720p, 1080i Видео декодирования совместимых с MPEG-2, MPEG-4 Входная скорость потока 2-45 Мсимв / с S / N> 53 дБ Аудио: Декодирование AC 3, MPEG-4 (HE-AAC), MPEG-1 Layer 1, 2 и 332/44.1/48 кГц S / N> 65 дБ Потребление: <25 Вт (мощность приемника - горизонтальная поляризация) сбор LNB 400 мА <20 Вт (мощность приемника, без LNB) <1 Вт (спящий режим) Электропитание 100-240 Вольт / 50-60 Гц ------------------------------------------------------------------------------ Linux устройства для сравнения: --------------------------------------------------------------------------------- Форум: http://forum.italysat.it/ http://www.et-view-support.com/Portal.php/ http://forum.sifteam.eu/ http://clarketech.funfiles.cc/index.php http://www.hdfreaks.cc/index.php?page=Index http://www.pli-images.org/forum/viewforum.php?forum_id=64#post_175778 http://www.wizardfox.net/clarke-tech-433/ctech-et9000-enigma-2-twin-tuner-25983/ http://www.et-support.com/forum/forum.php http://www.xtrend-community.com/ http://www.world-of-satellite.com/forumdisplay.php?174-Clarke-Tech-Xtrend-ET9000-Images http://www.vuplus-community.net/board/ http://aaf-board.com/forum/forum.php http://www.dreamboxuk.com/forums/forum.php http://www.et-view.com/ http://www.clarke-xtrend-support.com/Forum/forumdisplay.php?152- http://www.et-view.de/forum/index.php?page=Index Предупреждение всем владельцам оборудования ( ET - 9000 ) Никогда не следует удалить батарею устройства, как устройство будет терять свою память и нужно будет перепрограммировать в этом случае заводе и этот процесс занимает от четырех недель, как вам нужно нести расходы, связанные перепрограммированием
kladovchk: Power of Dream HD+ Image for ET-9000 17-08-2011 Changes: - Updated drivers - Vfd: cyrillic / greek charactermap Improvements - Scart: fix slowblanking - Alsa: fix pcm playback of high bit rate data - Fix mute status of ac3 passthrough mode in - Add 'use_advanced_remote - Add ioctl HDMI-CEC [hideguest]podhd-et9000.zip[/hideguest]
kladovchk: Power of Dream HD+ Image for ET-9000 New Image by SandBox Team based on Openpli 2.1 ATTENTION: - It is not possible to go from 2.0 to 2.1 by an updated online, it is mandatory to flash a 2.1 full - This new image requires an update of the bootloader before it can be installed [hideguest]podhd-2.1-et9000.zip[/hideguest]
kladovchk: EGAMI BACKUP 2011 08 20 .: MONSTER::. - Gotowiec, - ET5000 & ET9000 Hi, I'm a fan of software EGAMI, why? - Works 90% of the DVB-t - Works 90% of Wi-Fi card - Has NapiProjekt - Have a nice file manager - Fast and stabliny I decided to use the new version came with v1.2 namely Backup EGAMI Panel This is a panel where we can create fast backup settings / plugins / camów and other things. So when Egami v 1.3 comes out so we can upload the backup and we are in a minute we set + New Image! I decided to spend my Egami Backup panel. - Charter of C +, Polsat operates in slot - TNK HD module works - Channel list - HB - latest EgamiBackup is designed for people who want to upload, and no work - no combining. Egami Backup include: - CCcam 2.2.1 - OSCam - latest - FEED to CAMów - ASPECTRATIO Switch - CCcam Info - CCcamPrio Maker - DMNapi - Pernamental Timeshift - DreamExpoler - Free Memory - GlassSystem Utils - Live Football - MyTube - OSCam Status - Sundtek Control Center Requirements: - Egami v1.2 (DOWNLOAD) - File Egami_Backup to USB or HDD Installation: 1st Egami normal image uploading to the tuner v1.2 2nd Omjijamy configurator 3rd After installation, you must mount the device on which you have previously downloaded file 4th Press 2xZIELONY -> Devices Manager We'll see our connected devices we have in our ET [hideguest]20110820_EGAMI_Backup.egi[/hideguest]
kladovchk: EGAMI 1.3 ET-9000 Overview: - Image based on OE 1.6 - Kernel 2.6.18-7.4 - Drivers 27.06.2011 - Most of USB Wifi Dongles should works - Most of USB Tuners - DVB-C / DVB-T / DVB-S2 should works - UP to 2 dongles ! What's new ??? in v 1.3 - Improved OSD info in Infobar for OSCam - Improved HDMI-CEC driver ( thx to openstb git owner ) - now it is fully working HDMI CEC - Improved EGAMI File Manager - now it corretly PLAY .VOB files, some of them need to be PAUSED and then RESUMED to get playing... - Fixed WebInterface ( movie list ) - Fixed some "greenscreens" in File Manager - Fixed MyTube - Added EgamiBoot 1.0 - multiboot plugin - Added Image version info in Menu->Informations->About - Added Image version info on Bootlogos EgamiBoot 1.0 FAQ - READ HERE [hideguest]EgamiBoot v1.0 FAQ[/hideguest] Installed Plugins: - HDMI-CEC Support - BLIND SCAN Support - Videoenhacement Plugin - Web Interface - MyTube Player - FAN Setup - OSD 3D Setup - OSD Position setup - Cross EPG SVN 300 Buttons Mapping: OK button = LITE SKIN ( need to be turned on on GREEN PANEL -> EXTRAS -> OSD SETTINGS ) OK button x 2 = Extra Info Skin Blue button = EGAMI Blue Panel Blue button and then Yellow button = INFO Panel Blue button and then Blue button = EGAMI Settings Blue button long press = Extensions Yellow button = Time Shift Green button = EGAMI Green Panel Green button long press = Subservices Green button and then Red button = ADDONS Green button x 2 = EGAMI Settings Green button and then Yellow button = FILE MANAGER Green button and Blue button = SCRIPTS Button Red = EPG List Button PIP = Turn ON / OFF PIP Button PIP long press = PiP Menu - Move/Switch Windows Infobar: - CAM Name - ECM INFO - NETCARD INFO - CA INFO - TUNER INFO - CHANNEL INFO - NEXT EVENT INFO ( in channel list !! ) - AnalogicClock renderrer - Lite and Full infobar skin much, much and more... Egami Panel include: - Green button and then Red button takes You to EGAMI ADDONS MANAGER --> Download Egami Addons - Download extensions from Egami Server --> Manual Egami Addons Install - Install packages from /tmp --> Remove Egami Addons - Remove installed packages --> Download GUI Addons - Download CVS Extensions --> User Addons - Here You can install extensions from Your own server ( put in /etc/user_addon.txt url to catalog: example: http://your-feed-url...log_enigma2.xml ) - 2x Green button takes You to EGAMI Extras --> Kernel Modules Manager - start/stop kernel modules --> Devices Manager - here You can easily mount/map/format/settings Your extra memory storages like HDD, USB. REMEMBER TO MOUNT HDD BEFORE RECORDING !!! --> Services Panel - here You can Start/Stop/Check Status/Setting up: + NFS Server + HTTPD + Inadyn + Cron + DjMount ( UpNp Client ) + uShare ( UpNp Server ) + Syslog + Samba + OpenVPN + FTP + Telnet + Pcscd --> Mount manager - here You can mount Your networks share - CIFS/NFS --> Decoding Setup - You can disable some messages like eg. "Show Tune failed info?" --> Swap File settings - make Your swap file --> OSD Settings - Here You are able to Turn ON / OFF options like: Lite Skin, Orbital position, cam name, provider, crypt info in Infobar, Pernamental Clock, Picons and much much more... --> Stream Information - Get PAT/CAT/NIT/EIT/ECM Info --> USB Wifi & Tuner Dongles Setup - in this panel You can easily see what kind of Wifi or Tuner ( DVB-c/t/s2 ) you have connected to box and load drivers. The most complete info ever: Manfacturer, Vendor ID, ProID - Green button and then Yellow button run EGAMI FILE MANAGER --> You can Move/Copy/Remove/Rename Your files inside Your Box ! --> You can Create New Directory/New Text File/New Symlink ! --> You can change Permission of the files ! --> You can play all movies and music directly from Egami File Manager ! --> You can watch Your pictures from holiday directly from Your USB dongles by Egami File Manager ! --> You can start SHELL scripts --> You can start PYTHON scripts --> You can view most type of files by pressing OK --> 1st EVER - You can download Subtitles to Your movies stored inside your HDD - it finds subtitles exacly to version of the movie You have ! - available languages - ENGLISH, POLISH - more will come SOON... - Green button and then Blue button run EGAMI Scripts Panel --> You can run all scripts from /usr/scripts/ --> You can easily add new scripts to /usr/scripts/NAME_smartscript.sh and it will be visible in Scripts Panel OLD CHANGELOG What's new ??? in v 1.2 - EGAMI Backup Panel - now you can have severals backup of the EGAMI Image on severals connected devices to your STB - all backups are dated - so when you will make backup it will have new format: 20110712_EGAMI_Backup.egi - Egami Backup Panel -> When user makes backup - it is named like: DATE_Egami_BACKUP.egi - Egami Backup Panel -> Support for more than one backup on connected devices - user can choose which Backup he wants to restore - Egami Backup Panel -> Fixed Restore/Backup MultiQuickButton and CrossEPG ( About CoolEPG Restore - not done, because it install converters, it is not suitable to make for each plugin special backup logic ) - Also you can choose which backup you want to restore by moving UP/DOWN and after choose pressing BLUE button - Added text to inform user to press OK to reboot after Restore - Added default picon turned on as Reference read from /media/hdd/picon - Fixed user Add-on - Some Blue Panel skin improvements ( now it is listbox, not any more config ) - Some Blue Panel emu list changes - Samba conf workgroup changed to "workgroup" as a default What's new ??? in v 1.1 - Image include latest Front Processor - image include latest Bootloader - Latest Drivers -increase framebuffer acceleration memory size -always downmix audio on analog outputs -support /proc/stb/fp/was_timer_wakeup (needs frontpanel update) -vcr scart detection fix -vfd improvements -vfd: support greek and cyrillic charsets -vfd: support additional symbols (see /proc/stb/lcd/*) -pcm playback improvements -sci improvements -DVD Menu works OK - from ISO files also - Latest GUI - Latest GUI-Plugins - Added AC3+ / Dolby Digital + Support - Added zapUp /zapDown -> LEFT / RIGHT arrow - Added default cable.xml - thx pr2 - Added in FileManager option to play file by file -> most types of mulimedia files ( e.x 001.mts, 002.mts, 003.mts - You don't need to play one by one, it will be play from 1-3 ) - Added in File Manager < Root Directory > to make fast jump to / direcotry in Flash - Added in Mount Manager option to mount by UDP and TCP - Added animated pixmaps when We press RED to start CAM - Added in Decoding Setup -> Option to disable CI messages - Added Subtitles Menu on Subtitiles Button - Added Sleep Timer Menu on Timer Button - Added *.MTS extensions in MediaPlayer - Added Videoenhacement Plugin - Added EGAMI BackUp Manager -> You can backup/ restore EGAMI - You can install new egami, run this plugin and it will install things like emu, configs, plugins, etc... This tool allows You to flash by latest EGAMI Image but Keep Your favorite things inside !!! - Updated skin by Mimi - Updated French language by Mimi - Updated French language CrossEPG by Mimi - Fixed removing files from FLASH by EGAMI File Manager - Fixed Software Manager -> Install Local IPK - Fixed Marker - Fixed Button SAVE in FileManager Settings - Fixed Uninstaller SoftCams fixes ( killing before removing, if running softcam is removed, fall back to Common interface mode, if user remove other softcam, running softcam is still running ) - Fixed SoftCams change- it is 2 times faster now Credits Thanks to the group of Beta Testers. Thanks to Rytec for providing us with the server with all epg.dat files. Thanks to SiF Team for the nicest EPG plugin ever - CrossEPG Thanks to Skaman from SiF Team for extuner and usbloader DISCLAIMER THE EGAMI IMAGE IS BASED ON THE OFFICIAL FIRMWARE PUBLISHED BY XTrend AND IN ACCORDANCE WITH THE LAW IT CONTAINS ONLY SYSTEM ADDITIONS & GRAPHIC CHANGES. THE EGAMI IMAGE DOES NOT CONTAIN ANY EMULATOR, K E Y S, SOFTCAMS OR OTHER SYSTEM FOR VIEWING PAY - TV WITH OR WITHOUT A PAID SUBSCRIPTION. LASTLY, THE EGAMI IMAGE DOES NOT CONTAIN ANY SYSTEM TO DOWNLOAD PLUGINS OR EMULATORS FROM EXTERNAL SERVERS OR SOFTWARE THAT MAY BE USED FOR ILLEGAL PURPOSES SUCH AS CARD SHARING. LICENSE (TERM OF USE) THE EGAMI IMAGE IS ISSUED FOR THE FREE USE FOR ALL USERS PROVIDED THAT IT WILL NOT BE CHANGED IN ANY WAY AND THAT IT WILL ONLY BE USED FOR LAWFUL PURPOSES. ANY CHANGES OR ADDITIONS TO EGAMI IMAGE THAT INVOLVE UNLAWFUL USE OF THE IMAGE SUCH AS CARD-SHARING AND EMULATORS ARE NOT ALLOWED AND CAUSE THE REVOKE OF THIS LICENSE. www.xtrend-community.com [hideguest]egami-1.3-image-et9000-20110823.zip[/hideguest]
kladovchk: Black Hole 1.6.4a Full Hdmi-Cec - XTREND ET9000 and ET5000 YOU MUST TO HAVE LATEST BOOTLOADER !!! What is new in 1.6.4a? - Fixed GreenScreen on CrossEPG - Initial relase for ET9000 - VFD ALSO WORKS OK !!! What is new ? The new Black Hole Hdmi-Cec driver allow you to command two devices (Tv and Vu+ box) with only ONE Remote control (Tv remote control) Not all television are compatibile with this funcion, as for example Panasonic seems to be not yet compatible with Bh Hdmi-Cec. But Bh Hdmi-Cec is tested and report working on all latest Samsung(Anynet+), Philips and and other Tv models like Sony Bravia KDL40EX402 series. But we cannot test all tv recent models, so please help us reporting your tests too with your television model. Instructions to connect the box to your Hdmi-Cec compatible Tv: 1) Enter in your Tv Menu Options and enable all the Hdmi-Cec options. 2) Enter in your Vu+ box Black Hole Hdmi-Cec Panel Setup (blue->blue->Black Hole Hdmi Cec: Configure in this screen the right Hdmi connection port and enable Bh Hdmi-Cec. 3) Click Save (red) button and your box will try to connect with your Tv. All Done. If your Tv is compatible you can now control Tv and Box with Tv rc. Warning: You have to select the specific port option if your box is connected to an ampli. WARNING: This Image has the latest drivers and CAN NOT be installed in multiboot. The image MUST be installed in the flash. Black Hole can not support images not installed in the flash. This latest version of the Black Hole series has been entirely rewritten and improved in the code for maximum stability and performance. Please note that of all images Black Hole now has the best epg system: - Integrated OpenEpg - Rytec dedicated epg.dat - New system epg.dat outside. This last feature gives the possibility to various forums or communities to create their favorite EPG data files and load them into a web space. Community members can then download it from our servers. This feature provides other benefits such as: Increase download speed of EPG Download EPG from any channel Schedule the download of EPG decoder even during standby Users can customize the providers using Add / Remove function Main functions of the buttons on the remote OK button = Skin with simple information OK button x 2 = Extra Info Skin Blue button = Black Hole Blue Panel Blue button and then Red button = Black Hole Epg Panel Blue button and then Yellow button = System Monitor Panel Blue button long press = Extensions Yellow button = Time Shift Green button = Black Hole Green Panel Green button long press = Subservices Green button and then Red button = Fast Plugin Setup Green button x 2 = Fast Plugin Button Red = Start Record Credits DISCLAIMER LASTLY, THE BLACK HOLE IMAGE DOES NOT CONTAIN ANY SYSTEM TO DOWNLOAD PLUGINS OR EMULATORS FROM EXTERNAL SERVERS OR SOFTWARE THAT MAY BE USED FOR IILEGAL PURPOSES SUCH AS CARD SHARING. LICENSE (TERM OF USE) THE BLACK HOLE IMAGE IS ISSUED FOR THE FREE USE FOR ALL USERS PROVIDED THAT IT WILL NOT BE CHANGED IN ANY WAY AND THAT IT WILL ONLY BE USED FOR LAWFUL PURPOSES. ANY CHANGES OR ADDITIONS TO BLACK HOLE IMAGE THAT INVOLVE UNLAWFUL USE OF THE IMAGE SUCH AS CARD-SHARING AND EMULATORS ARE NOT ALLOWED AND CAUSE THE REWOKE OF THIS LICENSE. [hideguest]blackhole 1 6 4a et9000 image 20110907.rar blackhole_1_6_4a_et5000_image_20110907.rar[/hideguest]
kladovchk: Black Hole 1.6.5 Full Hdmi-Cec - XTREND ET9000 and ET5000 YOU MUST TO HAVE LATEST BOOTLOADER !!! What is new in 1.6.5? New Skin Beyounce 14 by Matrix 10 - Fixed GreenScreen on CrossEPG - Initial relase for ET9000 - VFD ALSO WORKS OK !!! - MEDIATOMB updated to ver. 0.12.1 - NTFS-3G updated to ver. 2011.4.12. - OpenVPN updated to ver. 2.2.1 - VsFTPd updated to ver. 2.3.4 - Dropbear updated to ver. 0.53.1 What is new ? The new Black Hole Hdmi-Cec driver allow you to command two devices (Tv and Vu+ box) with only ONE Remote control (Tv remote control) Not all television are compatibile with this funcion, as for example Panasonic seems to be not yet compatible with Bh Hdmi-Cec. But Bh Hdmi-Cec is tested and report working on all latest Samsung(Anynet+), Philips and and other Tv models like Sony Bravia KDL40EX402 series. But we cannot test all tv recent models, so please help us reporting your tests too with your television model. Instructions to connect the box to your Hdmi-Cec compatible Tv: 1) Enter in your Tv Menu Options and enable all the Hdmi-Cec options. 2) Enter in your Vu+ box Black Hole Hdmi-Cec Panel Setup (blue->blue->Black Hole Hdmi Cec: Configure in this screen the right Hdmi connection port and enable Bh Hdmi-Cec. 3) Click Save (red) button and your box will try to connect with your Tv. All Done. If your Tv is compatible you can now control Tv and Box with Tv rc. Warning: You have to select the specific port option if your box is connected to an ampli. WARNING: This Image has the latest drivers and CAN NOT be installed in multiboot. The image MUST be installed in the flash. Black Hole can not support images not installed in the flash. This latest version of the Black Hole series has been entirely rewritten and improved in the code for maximum stability and performance. Please note that of all images Black Hole now has the best epg system: - Integrated OpenEpg - Rytec dedicated epg.dat - New system epg.dat outside. This last feature gives the possibility to various forums or communities to create their favorite EPG data files and load them into a web space. Community members can then download it from our servers. This feature provides other benefits such as: Increase download speed of EPG Download EPG from any channel Schedule the download of EPG decoder even during standby Users can customize the providers using Add / Remove function Main functions of the buttons on the remote OK button = Skin with simple information OK button x 2 = Extra Info Skin Blue button = Black Hole Blue Panel Blue button and then Red button = Black Hole Epg Panel Blue button and then Yellow button = System Monitor Panel Blue button long press = Extensions Yellow button = Time Shift Green button = Black Hole Green Panel Green button long press = Subservices Green button and then Red button = Fast Plugin Setup Green button x 2 = Fast Plugin Button Red = Start Record Addons Green button and then Yellow button takes you to:- Dedicated server for BlackHole addons Download and install additional packages from the Black Hole server Infobar / OSD Analog Clock Gui Channel orbital location Advanced Tuner Info: Sr Freq Pol Fec Signal SNR, BER Infobar picons Characteristics of BlackHole Panels Blue Panel Extra Settings Black Hole Cron Manager (Manage schedules) OSD Settings (OSD configuration) Devices Manager Black Hole HDMI Cec Manager Kernel Modules (Kernel module web browsertor) Inadyn Settings (Configure Inadyn) Swap File Settings (Configure File Swap) Hard Disk Settings (Configure Hard Drive) Black Hole Mount Wizard (Mount points) OpenVPN Panel ( OpenVPN Panel) Samba / CIFS Panel ( Samba Panel) NFS Server Panel ( NFS server Panel) Telnet Panel ( Telnet Panel) FTP Panel ( FTP Panel) Usb Tuner Panel UPnP Client Djmount UPnP Server Mediatomb Info Panel 1 - Gui Setting (Gui configurations) 2 - Service Information (information system) 3 - About (info) Memory (Memory) Space (capacity) CPU (processor) Process (process) EPG Panel Global settings (global settings EPG) Setting Provider (ISP settings) Green Panel Fast Plugin Setup (Configure quick access to your favourite plugin) Fast Plugin (Access your favourite plugin) Addons (added) Addons Download Manager (Manager for package downloading) Installation manual packages (Manual installation of Black Hole packages) Manual Install IPK packages (Manual installation of IPK packages) Addons Uninstall Panel (Uninstalled packages) Black Hole Statistics (See connections, top downloads and more) Credits Thanks to the group of Beta Testers. Thanks to Rytec for providing us with the server with all epg.dat files. Thanks to MaxZ4 for Integrated EPG loader. Thanks to Sandro Cavazzoni for Cross EPG Thanks to Lukkino (VDR-Italy) for the source code of OpenTV. Thanks to Reinh@rd for the file satellites.xml. Thanks to bigroma (vuplus-community board) for rt3070 patches. [hideguest]BlackHole-1.6.5-et9000-20110920.rar click here[/hideguest]
kladovchk: Online update Power of Dream HD+ Image for ET9000 05/10/2011 - Modification of hypercam manager: the launch of enigmatic, verify that at least one local card is detected. If this is not the case, recovery hypercam. This should overcome the desire to hypercam etx000 on the launch. - Changes introduced by OpenPlant etxx00 linux -update routine Enigma2 To take the lastest update of POD Image just go to: Menu - Settings - Software Manager - Software update
kladovchk: ET-Toolbox v0.40 - EnigmEdit 1.38 hinzugefügt - Filezilla 3.5.1 -> neue Version hinzugefügt - Driver (Test) 20-08-2011 hinzugefügt - Driver 26-09-2011 hinzugefügt - Driver 30-09-2011 hinzugefügt - Bootloader 30-09-2011 hinzugefügt - Frontpanel Update 17-09-2011 hinzugefügt - Deutsche Bedienungsanleitung hinzugefügt [hideguest]ET-Toolbox_v0.40.zip[/hideguest]
kladovchk: HDF-Teamimage v4.2 16.10.2011 ET9x00 HDF-Teamimage v4.2 based on OpenPLi2.1 vom 16.10.2011 Clark-tech ET9x00 HDF Teamimage v4.2 basierend wie immer auf dem bewährten PLi 2.1. Den Ordner et9x00 auf einen USB-Stick entpacken, anstecken und den Receiver neustarten. Wer Probleme beim Flashen hat sollte versuchen den Ordner auf dem USB Stick in "ET9X00" (großes X) umzubennen. Das Plugin "Autoinstall" sollte im alten Image deaktiviert sein und es sollten keine alten Backups auf Platte oder Stick vorhanden sein. Sonst wird automatisch wiederhergestellt. Für das Image wird der aktuelle Bootloader benötigt. Der original Bootloader ist von hier: http://www.clarke-xtrend-support.com/Forum/showthread.php?3625-Bootloader Im Prinzip ist es ein HDF 4.1 auf die neue Struktur aktualisiert mit aktuellen Updates und Treibern. Wenn beim Setup kein Sendersuchlauf gemacht wird ist eine vorbereitete Senderliste enthalten. Hinweise zur Bedienung: Rot - Timer Editor Rot Lang - frei (Änderung über MultiQuickButton) Grün - Submenü Unterkanäle Grün Lang - frei (Änderung über MultiQuickButton) Gelb - frei (Änderung über MultiQuickButton) Gelb Lang - frei (Änderung über MultiQuickButton) Blau - Erweiterungen Blau Lang - Plugins Info - aktuelles Sender EPG Info Lang - Cool Single Guide Guide - Cool Multi Guide Guide lang - Cool Easy Guide Exit - Virtual Zap mit PIP Programm +/- schnelles zappen Steuerkreuz hoch/runter - Channel Selection Steuerkreuz rechts/links - schnelles zappen < > - Zap-History Filelist - Movie List Playlist - Media Player Timeshift - startet sofort Timeshift Vkey - Zugriff auf diverse installierte Plugins Vkey lang - TV Charts Plugin Mark - Timer Editor Search - EPG aktueller Sender Pip - Auswahl Pip und Pip Zap Modus Changelog: - Änderungen OpenPLi 2.1: http://twitter.com/#%21/openpli - Enigma2: http://openpli.git.sourceforge.net/git/gitweb.cgi?p=openpli/enigma2;a=shortlog - openembedded: http://openpli.git.sourceforge.net/git/gitweb.cgi?p=openpli/openembedded;a=shortlog - Plugins: http://openpli.git.sourceforge.net/git/gitweb.cgi?p=openpli/enigma2-plugins;a=shortlog enthaltene Plugins / Addons: - SHOUTcast mit funktionierender Aufnahme - MultiQuickbutton aktuelle Version, leicht angepasst - YTTrailer (TV, TEXT, RADIO Taste im EPG Overview -> Info Taste um Trailer zum aktuellen EPG Eintrag zu sehen) - Youtube Player (auch als Grundlage für YTTrailer) - Sport Portal (Formel 1und Fussball) - LiveFootBall - Dreamexplorer - InfoBarTunerState - Menusort - DTS Downmix Plugin - TV Charts (aktuelle Quoten der TV Charts Benutzer) - Wetter Plugins (Foreca, Wetter Informationen) - Bitrate Viewer (lang rot und Vkey) - Cool Multi Guide 5.0.0 - Oscam-Experimental mit vorbereiteten Configs für die Cardreader Wichtig!!! Aktueller Bootloader muss installiert sein. Der Bootloader ist von hier: http://www.clarke-xtrend-support.com/Forum/showthread.php?3625-Bootloader Bootloader im Anhang herunterladen und per USB-Stick wie ein Image installieren. Der Bootloader im Anhang ist der aktuelle Loader mit et9x00 Unterstützung. [hideguest]et9x00 hdfreaks.v4.2 PLi2.1 16102011.zip[/hideguest]
kladovchk: [center]ClarkeTech-Xtrend-Team proudly presents World Exclusive OpenPli2.1 beta Image based on Linux3.0.3 for ET9x00 little overview: - Improved dvb-usb like Vtuner, webcam - - Improved wifi usb devices - - Improved file system: UBIFS and EXT4 - - Improved streaming - - Improved picture quality and sound - - Improved overall preformance by about 10% - - and much more !!! - And again, ClarkeTech-XTrend-Team has done before all others! Others only talking, WE DO IT !!! Attention !!! - Plz du not Update yet - Updateserver are online in 2-3 Days !!! Attention !!! !!! Achtung !!! Bitte noch keine Onlineupdates ausführen! Die Server werden in 2-3 Tagen angepasst. !!! Achtung !!! --- This is only a Beta Version plz report all bugs what you found here --- --- Es handelt sich noch um eine Betaversion, daher bitte jegliche Fehler wo ihr findet hier Posten danke --- !!! Needs the latest Bootloader (30.09.2011) from here LINK !!! !!! Benötigt den aktuellen Bootloader (30.09.2011) von hier LINK !!! Special Thx to: wallie2000, tam2010, dispatcher, Biki3, z-pg-3, janosch, Pcd, CoolST, clarkemaster, memo and all other devs! viel spass damit grüße ice... *ein thx wäre schön*[/center] [hideguest]openpli-2.1-et9x00-20111016151229_usb.zip[/hideguest]
kladovchk: Clarke-Xtrend Support Image V3 Этот образ основан на Linux 3.03. Поэтому необходима последняя загрузчик 30.09.2011! и сначала установить процедуры, необходимые для Linux основанный 3,03 openpli et9x00 изображения. Также важно - пожалуйста, прочтите Readme в КТ панель для изображения используйте инструкции Important This image is based on Linux 3.03. Therefore it requires the latest bootloader 30.09.2011! and first install procedure necessary for the Linux 3.03 based openpli et9x00 image. Also important - please read the Readme in CT Panel for image use instructions Clarke-Tech Enhancements for the completely modular Image - Clarke-Xtrend HD Lava Skin with pig (picture in graphic) in many menus - Clarke-Xtrend Bootlogos and Radio Logo - Clarke-Xtrend Panel Please see attached Screenshots for a short overview of all Parameters - Best Sysinfopanel (complete overview of systemparameters) - HDMI-CEC Support via Plugin - WLAN fixes and support for 80211b/g/n Ralink, Realtek, Carl based USB-Dongles (rt2800USB, rtl871x, AR9170) - Running "broken" Shellscript (as Cronjobs) will work - Acousticpatch (needs a HDD that supports acoustic parameter consult HDD manufacturer for this) Highlights: -Clarke-Xtrend Webbrowser HbbTV. This image fully supports the unique Webbrowser HbbTV for more info see the readme or visit our forum. -Daemon Manager. For information - a daemon is a computer program that runs in the background. The daemon requires a start/stop script - the script must be executable (chmod 755), placed in /etc/init.d and the name must start with "dmon." Switch Mode You can choose the way you want the Main Menu to be displayed choose between "text, icon or scroll". Please change it in Settings / System / Customize / mainmenu list option - CT News Feed Clarke-Xtrend FEED Contents : - Driver - Games - picons - Plugins - Setting - Skins - systemPlugins - Update Plugins added CT-Panel AudioSync CutListEditor EPGImport GlassSysUtil GraphMultiEPG MediaPlayer MediaScanner PicturePlayer Tuxtxt WebMedia Backup-Suite Specialised version of MultiQuickbutton for Clarke-Tech ET9000 can be downloaded from CT feed. Code: 1. Zurück <: Zap History - 2. Vor >: Zap History + 3. Farbtasten Rot: Rot (lang): Grün: Auswahl Optionskanäle Grün (lang): Gelb: Audio-Einstellungen Gelb (lang): Blau: Erweiterungsmenü Blau (lang): 4. GUIDE: Programmübersicht GUIDE (lang): 5. INFO (i): Programmübersicht INFO (i) (lang): 6. MENU (Lang): 7. EXIT: Infobar 8. OK: Infobar 9. Steuerkreuz Runter: Kanalliste Links: Sender zur\'fcck - Rechts: Sender vor + Auf: Kanalliste 10. VOL. +/-: ** 11. P+: Kanalliste P-: Kanalliste 12. Filelist: Aufnahmen Filelist (lang): 13. Playlist: Playlist (lang): 14. zurückspulen << : 15. vorspulen >>: 16. Play/Pause >II: Starte Timeshift 17. REC: Aufnahmemenü REC (lang): 18. Slowmotion I>: *** 19. Stop: Stoppe Timeshift 20. Timeshift: Starte Timeshift Timeshift (lang): Stoppe Timeshift 21. search: serach (lang): 22. Mark: Mark (lang): 23. Timer: Timer (lang): 24. Vkey: Aufnahmen Vkey (lang): 25. PIP: Bild in Bild PIP (lang): Tausche Bild in Bild 26. TEXT: Teletext TEXT (lang): 27. subtitle: Untertitel subtitle (lang): Untertitel-Einstellungen 28. AUDIO: Audio-Einstellungen AUDIO (lang): 29. TV: TV TV (lang): 30. Help (lang): 31. RADIO: Radio RADIO (lang): Special thanks: pcd (Main Developer) wallie2000 (Image-Support) Clarkemaster(Skins,Bootlogos) All Betatesters (Coolman, CoolST, icewaere, csm, dispatcher, tam2010, z-pg-3, Biki3, janosch ) mogli123 (MQB). Pedro_newbie (image backup plugin) Pli team (for the image background code) All the other code developers and plugin developers a big thanks to ClarkeBoss [hideguest]clarke-xtrend-et9x20111027133804_usb.zip data_et9x00-bootloader.zip[/hideguest]
kladovchk: DreamboxUK_v2.1_ET9x00, ET5x00 Base: OpenPLi 2.1 Enigma: 01-11-2011 Kernal: 3.0.3 r5 Drivers: 29-10-2011 Skins:- Magic Magic-EHD Cams:- CCcam 2.2.1 Plugins / Extensions:- AudioSync WebInterface CCcamInfo v1.3c CrossEPG SVN 306 OpenVPN Graphical Multi-EPG Device Manager Backup Manager File Installer System Tools & Info Bouquet Updater Picon Updater Swap Manager Cron Manager VirtualZap lots of enigma2 updates more uk regions added to bouquet updater, some removed removed licher picons from picon updater dts downmix added ntfs support added smargo drivers added more wireless drivers added Button Mappings removed, install multiquickbutton from the addons panel and setup to how you like it + more... [hideguest]DreamboxUK_v2.1_ET9x00.rar[/hideguest]
kladovchk: OpenPli 2.1 Linux3.1.0 beta Image 06.11.2011 ClarkeTech-Xtrend-Team & OpenPli Team proudly presents World Exclusive OpenPli2.1 beta Image based on Linux3.1.0 for ET9x00 little overview: - framebuffer console - - vtuner fixes - - Improved wifi, dvb-t, dvb-s2 usb devices - - and much more !!! - And again, next strike from ClarkeTech-XTrend-Team & OpenPli Team ! --- This is only a Beta Version plz report all bugs what you found here --- --- Es handelt sich noch um eine Betaversion, daher bitte jegliche Fehler wo ihr findet hier Posten danke --- !!! Needs the latest Bootloader (30.09.2011) from here LINK !!! !!! Benötigt den aktuellen Bootloader (30.09.2011) von hier LINK !!! Special Thx to: wallie2000, tam2010, dispatcher, Biki3, z-pg-3, janosch, Pcd, CoolST, clarkemaster, memo and all other devs! [hideguest]OpenPLi-2.Kernel-3.1.beta-et9x20111106_usb.zip[/hideguest]
kladovchk: BackupSuite для ET9000 Here is a new version of the backup suite based on a new concept. The code had to be cleaned up, because it was hard to let it run cleanly. Some things you should know: - First remove the old version that can be done as follows: Menu -> Remove red button Plugins - -> Extensions> system plugins -> backup suite <language> If this does not work, you can try it with telnet opkg remove "eni gma2-plugin-system-backup suite *" - force-removal-of-dependent-packages or opkg remove "eni gma2-plugin-system-backup suite *" - autoremove You should look on the box if the folders are gone, they are usually in / usr / lib / eni gma2/python/Plugins/SystemPlugins/Combi-HDD-Backup / and / usr / lib / eni gma2/python/Plugins/SystemPlugins/Combi-USB-Backup / These two folders should now be gone. Restart after uninstalling the box please once again with "Restart eni gma2" Then install the new version. The new folder for the backup suite can be generated in / usr / lib / eni gma2/python/Plugins/Extensions/BackupSuite-HDD / and / usr / lib / eni gma2/python/Plugins/Extensions/BackupSuite-USB / There are now only one package called backup suite (eni gma2-plugins-extensions-backupsuite_ <version>, currently V6.7), there are no more different languages. Please feel free you to test this new version, I'm open to suggestions and changes to the German translation. A final word: this version needs to install an Internet connection to necessary files such as. mkfs.ubifs reload. Вот новая версия пакета резервного копирования на основе новой концепции. Код должен быть очищен, потому что было трудно дайте ему поработать чисто. Некоторые вещи вы должны знать: - Сначала удалите старую версию, что можно сделать следующим образом: Menu -> Красная кнопка плагинов - Удалить - ->Extensions - Расширения> system plugins - Система плагинов -> резервного копирования пакета <language> Если это не работает, вы можете попробовать его с Telnet opkg удалить"eni gma2-plugin-system-backup suite *"- форс-удаления, из-зависимой-пакеты или opkg удалить "eni gma2-plugin-system-backup suite *" - autoremove Вы должны смотреть на поле, если папки нет, они, как правило, в / usr / lib / eni gma2/python/Plugins/SystemPlugins/Combi-HDD-Backup / и / usr / lib / eni gma2/python/Plugins/SystemPlugins/Combi-USB-Backup / Эти две папки должна исчезнуть. Перезагрузка после удаления окна пожалуйста, еще раз с "Restart eni gma2" Затем установите новую версию. Новую папку для резервного копирования пакета могут быть сформированы в / usr / lib / eni gma2/python/Plugins/Extensions/BackupSuite-HDD / и / usr / lib / eni gma2/python/Plugins/Extensions/BackupSuite-USB / Есть в настоящее время только один пакет, называемый резервный набор(enigma2-plugins-extensions-backupsuite_ <version>, currently V6.7), Есть не более разных языках. Пожалуйста, не стесняйтесь вам протестировать новую версию, я открыт для предложений и изменений в немецком переводе. Последнее слово: эта версия требует установки Интернет-соединения с необходимыми файлами, такие как. mkfs.ubifs перезагрузки. [hideguest]enigma2-plugin-extensions-backupsuite_6.7_mipsel.rar[/hideguest] Here's a new version, with better localization (umlaut allowed!) Also available after the next nightly build Вот новая версия, с лучшей локализации (умляут допускается!) Также доступны после очередного ночные сборки [hideguest]enigma2-plugin-extensions-backupsuite_6.9_mipsel.rar[/hideguest] BackupSuite 7.0 And yet another new version, version 7.0. This time some corrections in the languagefile(s) and an new translation, French! (Thanks Demosat!) It could be that some й и б ь etc leters are still missing because of the first versions a wrong code was used and the special character got lost in translation. If there are persons who want to add another language feel free, in the folder locale is a .po file with the name Default.po, this file can be used to add a language. The file can be edited by any texteditor or with the program Poedit which can make a translated file (.mo) Poedit can be found at: Here I also forgot to thank Biki3 and Bonsai Baum for their German translations. The new version is attached at the end of this message. Here are some screens from the French version [hideguest]enigma2-plugin-extensions-backupsuite_7.0_mipsel.rar[/hideguest]
kladovchk: driver 3.0.3 linux ET9000, 9200 drivers 2011-10-29 [hideguest]data_et9x00-drivers-3.0.3-20111029.zip[/hideguest] New driver 3.1.0 linux ET9000, 9200 drivers 2011-11-05 [hideguest]data_et9x00-drivers-3.1.0-2011-11-05.rar[/hideguest] copy and replace the 4 extracted Files here: /lib/modules/2.6.31-3.2/extra reboot. Установка: Скопируйте и замените 4 извлеченных файла, здесь: /lib/modules/2.6.31-3.2/extra Перезагрузите
kladovchk: ETTimeDrift ETTimedrift Version 1.2 1.2 - Neu: Englisches Grundpaket mit deutscher Lokalisierung. [hideguest]enigma2-ettimedrift_1.2-20110904_mipsel.rar[/hideguest]
kladovchk: Webbrowser - Integrate red button function. For the skins there must be add an icon which is linked to: <convert type="ServiceInfo">HasHBBTV</convert> - Compatible with allmost all mouse and keyboards - Youtube player ( http://www.youtube.com/xl ) - Mediatheek supports ( NPO Netherland, ZDF/ARD/PRO7/RTL Germany and much more) - Online radio with tuneinradio - Weather and rain forcast - Traffic jams with TOMTOM and lot lot more !!!!!!! The webbrowser can been found (after installation and reboot of the box) under the blue button. With the menu button it opens a window where you can choose the mode or bookmarks. TV Channels which have a hbbtv portal can easily been opened through red button. Need help in webbrowser use then help button The bookmarks can been found in directory /etc/enigm@2/ - Интеграция красную функциональную кнопку. Для шкуры должны быть добавить значок, который связан с: <convert type="ServiceInfo"> HasHBBTV </ конвертировать> - Совместимость с allmost все мыши и клавиатуры - Youtube игрока (http://www.youtube.com/xl) - Mediatheek поддерживает (НПО Нидерланды, ZDF/ARD/PRO7/RTL Германии и многое другое) - Интернет-радио с tuneinradio - Погода и дождь погоды - Пробки с TOMTOM и многое многое другое !!!!!!! Браузер можно было найти (после установки и перезагрузки коробки) под синюю кнопку. С помощью меню кнопки открывается окно, где вы можете выбрать режим или закладкам. Телеканалы, которые hbbtv портала может с легкостью был открыт через красную кнопку. Нужна помощь в использовании браузер затем кнопку справки Закладки можно было найти в каталоге / и т.д. / enigm @ 2 / [hideguest]enigma2-plugin-extensions-et-webbrowser_1.0-r0_et9x00.ipk.rar[/hideguest] Hey, you've built a fix, the function of the RedButton browser v1.0 also works with multi-button quick V2.8.1 The red button can, of course, by then no longer be adjusted MQB! Fix for multi-button quick V2.8.1 RedButton that works on new web browser v1.0 After this fix, you cannot change anymore on RedButton MQB. First MQB281_Webbrowser_v1.0.zip unpack and copy to "/ usr / lib / enigme 2/python/Plugins/Extensions/MultiQuickButton @ / '/ replaced. Second Reboot [hideguest]MQB281_Webbrowser_v1.0.zip[/hideguest]
kladovchk: MultiQuick button: 2.8.2 (for the et-serie) 2.8.2 info: - Info: on / off book now can be used without a restart and will be equal change in re-read - Ok / exit: on / off can be used without the book now restart - On the key 3 in the main menu is now: Query keys: on / off so it is now possible if not for a MQB occupied key starts the query like this should be documented that goes without having to restart - Is the info about yourself on the "i / info" button in the Main Menu-MQB no longer as before on the 3 (yes interested but eh no * gg *) - Advanced "4:3 / non-linear scaling, etc. .." (Thank you Bonsai Baum) - Press the "rewind <<" now works properly - New function "Play / Pause time shift" contain all the buttons (thanks PinBot) New-function "HbbTV (Red Button)" contain all the buttons your existing settings to version 2.8.1 to 2.8.2 this does not be used to restore / use ... adapted for co-standard (et9x00, et5x00, et6x00) ATTENTION: who wants to use the multi-button quick here its previous version must be installed MQB x (if available) please first uninstall ps all changed keys / assignment / assignments have not influence on the behavior / control the plugins / programs themselves ... that is, if I as a bsp. on the button "stop" me "teletext" lege and then for example in the "Media Player" RECOURSE am the taste as "Stop" function get Note: If you have already made adjustments to them after overwriting the files will be made again! my thanks for the existing MQB source goes to "emanuel", "Renew" "Plnick" and of course the entire team-et here as well as individual user here in the forum ... 2.8.2 info: - info:an/aus kann jetz ohne restart verwendet werden und wird gleich bei änderung neu eingelesen - ok/exit: an/aus kann jetz ohne restart verwendet werden - auf der taste 3 im hauptmenü befindet sich jetzt: Tastenabfrage: an/aus damit ist es nun möglich ob MQB bei einer nicht belegten taste die abfrage startet wie diese belegt werden soll das geht auch ohne restarten zu müssen - die about info befindet sich jetzt auf der "i/info" taste im hauptmenü-MQB also nicht mehr wie vorher auf der 3 (interessiert ja aber eh keinen *gg*) - Erweiterte "4:3 / Skalierungen NichtLinear usw..." (danke Bonsai Baum) - Taste "Zurückspulen <<" funktioniert jetzt richtig - neue Funktion "Play/Pause Timeshift" für alle Buttons enthalten(danke PinBot) -neue funktion "HbbTV (Red-Button)" für alle Buttons enthalten eure vorhandenen 2.8.1 settings können in dieser 2.8.2 version nicht wieder eingespielt/verwendet werden ... angepasst für die et-serie (et9x00, et5x00, et6x00) Tasten die leider nicht/oder auch noch nicht funktionieren (zwecks fehlender Key ID zuweisung) sind: I> slowmotion play taste ACHTUNG: wer das MultiQuickbutton hier benutzen möchte muss seine vorherige installierte MQB Version x (falls vorhanden) bitte erst deinstallieren p.s alle veränderten tasten/belegung/zuweisungen haben keinerlei einfluss auf das verhalten/steuerung der plugins/programme selbst ... das heisst wenn ich als bsp. auf die taste "Stop" mir den "teletext" lege und dann bspw. im "Mediaplayer" bin bliebt die taste als "Stop" funktion erhalten Hinweis: Wenn man bereits Anpassungen vorgenommen hat, müssen diese nach dem Überschreiben der Dateien erneut vorgenommen werden! mein dank für die vorhandene MQB source geht an "emanuel", "ReneW", "plnick" und natürlich dem gesamten et-team hier so wie auch einzelne user hier im forum... [hideguest]enigma2-plugin-extensions-et-multiquickbutton_r2.8.2_mipsel.ipk[/hideguest] BackupSuite 7.3 Еще одна новая версия BackupSuite, версии 7.3 теперь поддерживает польский язык. Поддерживаемых языков теперь: английский (по умолчанию), голландском, французском, немецком, польском и русском языках. [hideguest]enigma2-plugin-extensions-backupsuite_7.3_mipsel.ipk[/hideguest]
kladovchk: ET9x00 HDF-Teamimage v4.3 based on OpenPLi2.1 vom 25.11.2011 So hier dann mal das aktuelle Bastelimage 4.3 von uns. Es handelt es um das HDF-Teamimage 4.2 komplett aktualisiert. Update Stand ist vom 25.11.2011 20:57 Uhr. Enthalten sind die aktuellsten Versionen der installierten Plugin und das HbbTV Plugin. Außerdem ist das neue OpenWebif dabei. Zu erreichen über http://IP-Adresse_der_Box:8088. Skin ist der army.pli in einer gemoddeten Version mit HbbTV Anzeige und ein paar anderen kleinen Sachen. Die Picons können über die HDF-Toolbox nachinstalliert werden. Именно к команде Изображение HDF 4,2 полностью обновлен. Дополнение тактовой 11/25/2011 20:57 'ов. Включены последних версий установленных плагинов и плагинов HbbTV. Кроме того, новые OpenWebif есть. Доступ через http://ip-adresse_der_box:8088/. Кожа модифицированные версии с army.pli HbbTV дисплей и некоторые другие мелочи. Picons может быть установлен из HDF-панели инструментов. [hideguest]et9x00_hdfreaks.v4.3_PLi2.1_25112011.zip[/hideguest] FanSetup ver.3.0 Plug-mode parameters of the fan ET9000. There was an additional mode "combination". Where you can specify a specific time on / off / auto. example: Quiet hours 15:00 to 16:00, the fan is turned off. Plug-режиме параметры вентилятора ET9000 Существовал дополнительный режим "Комбинация". Где вы можете указать определенное время вкл / выкл / авто. пример: Тихий час с 15:00 до 16:00, вентилятор выключен. [hideguest]enigma2-plugins-systemplugins-fansetup_3.0_mipsel.ipk[/hideguest]
kladovchk: В общем имидж нормальный, всё необходимое есть. Эмулятор mgcamd работает Добавил в папку key newcamd.list и добавил в SoftCam.Key несколько biss ключей, например на Astra 1G @ 31.5° East : F 1B5E1FFF 00 хххххххххххххххх ; TV Centr International (31.5°E) F 1B5E1FFF 01 хххххххххххххххх ; TV Centr International (31.5°E) F 1b591b59 00 хххххххххххххххх ;First Ukr (31.5°E) F 1b591b59 01 хххххххххххххххх ;First Ukr (31.5°E)
полная версия страницы